Full T-shirt base layer from Forecfield. Front armour, back armour, shoulder armour and elbow armour. The best product we have found so far for Vietnam's hot weather. Breathable holes going through all the armour pads, light weight pads and a stretchy t-shirt material.
Forcefield is a UK based company, mostly known for its premium Armour that goes in other brands. However this is Forcefields own lineup of gear.
Material that is too hard transfers crash energy directly to your body. Material that is too soft bottles out on impact. Forcefield is known for a premium blend that minds the perfect balance of soft and hard for impact perfection.
Forcefield Pro Shirt X-V 2
The Pro Shirt X-V 2 features a complete set of CE Level 2 armor in the back and chest and Isolator 2 CE Level 2 armor shoulders and elbows. Wear the Pro Shirt X-V 2 under your moto jacket for Level 2 CE Protection.
- X vents provide increased airflow
- Armor windows providing extra venting
- Lightweight and breathable BeCool base layer fabric
- Lightweight removable armor
- Isolator 2 CE Level 2 armor is 12mm thick
- Repeat Performance Technology (RPT)
- DRI-M Technology (Dynamic, Reactive, Intelligent Material)
QUESTIONS & ANSWERSAsk a Question
Miếng giáp ở bên trong có tháo được không ạ?
Miếng giáp ngực, lưng cùi chỏ và vai đều có thể tháo ra được để vệ sinh giặt giũ. Tất cả các miếng giáp đều đạt chuẩn CE Level 2
Forcefield Proctective size chart
* Sizing information is provided by the manufacturer and does not guarantee a perfect fit.
|Pro Tube X-V 1&2||Elbow/Knee joint||10" - 12"||12 1/4"- 15 3/4"||16"+|
|Pro Shorts X-V 1 & 2||Waist||30" - 33"||34" - 37"||38" - 41"||42" - 45"|
|Pro Shirt X-V 1 & 2||Chest||35" - 39||40" - 44"||45" - 48"||49" - 53"|
How to measure
- KNEE (ABOVE)
- Measure your leg circumference, 1 inch above your kneecap.
- ELBOW (AT THE JOINT)
- Measure the widest circumference of your elbow over the elbow joint, with your arm bent at a 45° angle.
- Measure around your natural waistline, around the top of the hip bones, inline with the navel while keeping the measuring tape parallel to the ground.
- Measure around the fullest part of your chest, under the armpits, keeping the measuring tape parallel to the ground.
The most important helmet fitting aspect to consider before determining helmet size is helmet shape. The shape of the rider's head plays a crucial role in selecting a proper fitting motorcycle helmet. All helmet manufacturers design their lids to fit a specific head shape. These often range across three primary designations - long oval, intermediate oval, and round oval.
- Long Oval - Shaped for a head which is longer front-to-back (from forehead to the back of the skull) than it is side-to-side (ear to ear).
- Intermediate Oval - Shaped for a head which is slightly longer front-to-back than it is side-to-side. Most motorcycle helmets will fall into this category as it is the most common head shape; if a helmet does not state its shape, this is usually it.
- Round Oval - Shaped for a head which has almost identical front-to-back and side-to-side measurements.
Once the head shape is determined, it is easier to filter the enormous selection of available motorcycle helmets down to a smaller, more appropriate list of those which will fit the rider's head. Now it is time to find the correct size of the motorcycle helmet.
Helmet Safety Standards
DOT Helmet Standard: This stands for “Department of Transportation,” (not “doin’ our thang”) but the standard is FMVSS 218, the Federal Motor Vehicle Safety Standard #218, Motorcycle Helmets, and it is applicable to helmets sold in the U.S. for on-road use.
ECE 22.05 Helmet Standard: ECE stands for “Economic Commission for Europe,” which was created under a United Nations agreement in 1958. The 22.05 part refers to the specific regulation that the standards for testing are described in.
Snell (Snell Memorial Foundation M2010) Helmet Standard: The Snell Memorial Foundation is a private, non-profit organization formed in 1957 dedicated to improving helmet safety. Snell goes beyond the governmental standard-setting approach and is available to assist manufacturers with helmet development by offering prototype testing.
What is MIPS technology? MIPS stands for Multi-directional Impact Protection System, which is a leading slip-plane technology inside the helmet designed to reduce rotational forces that can result from certain impacts. MIPS has been developed by leading brain surgeons and scientists to reduce the rotational forces on the brain caused by angled impacts to the head.